WiFi Communication Between Two ESP8266 Based MCU Through the Home Router

Some months ago I started to experiment ESP8266 based NodeMCU and Wemos boards. At first I used them (in my previous POI hunter project) as a smarter Arduino, because they have higher clock frequency, more memory and built in "SD card" (SPIFFS).

In my Arduino projects sometimes I had to send messages between two MCUs. I used wired communications (serial, i2C) and wireless (bluetooth, RF transmitter / receiver and nRF24). So there was not question I will face this topic using ESP modules also.

I started to mine the internet for ready samples but I didn't find an easy solution for MCU-MCU WiFi communication. Finally I started from the basics. According to the description of the Arduino WiFi library and the WiFi library for ESP8266 I made what I wanted.

In the next pages I will share the result with you in two versions. At first two bare MCU will demonstrate the bare minimum solution of the TCP communication. After that I will show an easy application using an additional DHT22 sensor and some OLEDs.

Step 1: Bare Minimum, TCP Communication Between Two ESP8266 MCUs

Yo can see any HW you need in the picture. Only two MCUs (and a PC).

Both MCUs connect to your home WiFi router. (Don't forget to put your SSID and password into the code before upload the code.) One of the MCUs will be a server and the other will be the client. The client triggers the communication asking the server and the server will send an answer. Modifying the messages you will be able to send anything between the two modules.

Your router will give IP addresses to your MCUs during the connection. Launching the server you will see its IP address in the lower row of the OLED. You have to put this IP into the client's program, because the client will connect to the server using this address. Running the devices some days later you server will receive different IP address, and you will need to modify the client program again. To avoid this annoying thing give fix IP address to your server.

Things you have to do to launch the server:

Connect one MCU to a PC with USB cable.
Open the "wifi_server_01.ino".
Replace the asterisks "****" with the SSID and the password of your home WiFi router.
Open the settings of your home WiFi router and choose a free IP address which is out of the DHCP range.
Set the IP of your server (row15).
Gateway will be the IP of your WiFi router.
Upload the program.
Run the serial monitor of the Arduino IDE.

Things you have to do to launch the client(s):

Run an additional Arduino IDE.
Open the "wifi_client_01.ino".
Replace the asterisks "****" with the SSID and the password of your home WiFi router.
Put the IP address of your server into the 15th row.
Upload the program.
Run the serial monitor for the new Arduino IDE also.

The client connects to the server soon and you have to see the received messages in both terminal windows. During the communication the built in LEDs will flash for a short time.

Step 2: DHT Server With Clients

Here is an application which uses the TCP communication between ESP8266 MCUs.

A Wemos server listens, reads the DHT22 and shows the temperature and its own IP address on a small OLED screen. Two NodeMCU clients trigger the server and receives the temperature value as the answer. During the communication the server's OLED switches to inverse.

There is only a small modification in the server's program. After some hour work it sometimes stopped serving the clients. It readed the DHT22 and refreshed the OLED, but clients didn't received any answer. To solve this problem I started a timer. The program resets it after serving a client. If the timer reaches 30000 (30 seconds), the server disconnects from the WiFi network and reconnects again.

According to the attached schematics you can build the server and client hardware. Uploading the programs you will have a remote thermometer. Modifying the programs you can build your own project in which the ESP8266 based MCUs can communicate with each other.

Of course every device connected to your local network will be able to ask the DHT server. You can see a screenshot about my mobile also.

Oscar perez

Arquitecto especialista en gestion de proyectos si necesitas desarrollar algun proyecto en Bogota contactame en el 3006825874 o visita mi pagina en www.arquitectobogota.tk

WiFi Communication Between Two ESP8266 Based MCU Through the Home Router